ccna 2.5 quiz

1.when configuring an ISR device using cisco SDM express wizard,what does setting the enable secret password field accomplish?

·         Ensures that authorization must be granted before accessing the internet

·         Blocks unauthorization users from accessing the LAN

·         Controls access to user executable mode

·         Controls access to privileged mode

2.when using cisco SDM,which WAN encapsulation type can be configured to require a username and password before a connection is granted?

·         High level data link control(HDLC)

·         Frame delay

·         Point to point protocol(PPP)

·         ATM PVC

3.what speed and duplex setting will result on a catalyst switch if it is set to auto negotiated to a 100Mbps port on a device that does not support auto negotiation?

·         10 half duplex

·         10 full duplex

·         100 half duplex

·         100 full duplex

4.which method can be used to configure a cisco catalyst switch before an IP address has been applied to the management interface?

·         Cisco IOS CLI using vlan 1

·         Cisco IOS CLI using console port

·         Cisco device manager using console port

·         Cisco software using vlan 1

5.what is a secure way that a client can connect to a device in band for the purpose of remote monitoring and administration?

·         telnet

·         HTTP

·         SSH

·         Console port

6.which type of wide area network(WAN) connection uses packet switched networks?

·         ISDN

·         Dial-up

·         Frame relay

·         Point to point

7.a small company with two office in the same building is requesting advice on WAN connections.which two questions would give a technician information to base a recommendation?(choose two)

·         What operation system is being used?

·         How much money has the customer budgeted to spend on the WAN connection?

·         What type of email client software is used by the employees?

·         Are the computers laptops or workstation?

·         Are the company web servers located in the building or at the ISP?

8.what is one fundamental difference between cisco’s CLI versus the SDM interface?

·         The SDM interface can be used with both in band out of band management

·         The CLI interface can be used with both in band and out of band management

·         The SDM interface requires a terminal emulation program on the PC

·         The CLI interface cannot be used over a telnet connection

9.which two statements describe the command history feature?(choose two)

·         It requires configuration of a history buffer before it can be used

·         It displays the most recently entered command strings in the current mode

·         It saves the output from the most recent show command

·         It displays the last five command that were entered in global configuration mode

·         It can be accessed by using the up and down arrows keys

10.which router mode displays a prompt of router#?

·         Global configuration mode

·         Privileged EXEC mode

·         Setup mode

·         User EXEC mode

11.in which two cases would out of band management of a router be required?(choose two)

·         When accessing a customer router ftom the ISP to monitor the normal operation

·         To access and configure the router before the ISP network is operational

·         To correct an error that has shutdown the network interfaces on a router

·         When the NAT translation configuration settings are incorrect

·         To back up the running configuration on the a tftp server

12.which two statements describe the result of entering the IP route 0.0.0.0 0.0.0.0 192.168.1.1 command on a router?(choose two)

·         The router is not able to reach the 192.168.1.0 network

·         All packets received by the router are sent to the address 192.168.1.1

·         The remote network 192.168.1.0 can be reached using any interface

·         A default static route is added to the routing table

·         If a route to a destination network is not known,the packet is sent to 192.168.1.1

13.click and drag the command on the left to the correct category on the right

Used to change router modes or sub modes

Configure terminal

Interface fastethernet 0/0

enable

Used by administrator to verivy or monitor router operation

Show ip route

Show interfaces

ping

Affect the operation of the network

Ip address 172.16.1.1 255.255.255.0

No shutdown

14.what is the purpose of assigning an IP address to the interface VLAN1 on the cisco switch?

·         To be able to telnet to the switch to manage and configure it

·         To enable the switch to route between network

·         To create a new IP local network on the switch

·         To permits IP packets to be forwarded by the switch