Minggu, 14 November 2010

ccna 2.2 quiz


1.click and drag the network function on the left to the correct layer that they belong to on the right
TRANSPORT LAYER
Packages data in segments for transmission
Uses for UDP for realtime data streaming
Adds port numbers
NETWORK LAYER
Routes packets between networks
Adds ip addresses to data packets
Encapsulates data in packet for transmission
2.using a systematic troubleshooting approach,a help desk technician suspect a problem at layer 3 of the OSI model.which two question could be asked to isolated the problem to layer 3?(choose two)
  • IS YOUR PC CONFIGURED FOR DHCP
  • Can you browse to www.cisco.com?
  • Is your network cable plugged in?
  • CAN YOU PING YOUR DEFAULT GATEWAY?
  • Do you see a link light on your network cards?
3.click and drag the question on the left to the correct order on the right if a help desk technician is using a bottom up approach to troubleshooting
Question 1

Is your network cable securely connected?

Question 2

Do you see a link light on your network card?

Question 3

What is the subnet mask on local area conection 2?

Question 4

Is your firewall blocking port 25?
Question 5
What mail server is listed in the outgoing server setting?
4.a customer call has been escalated to an on site technician because the level 1 and 2 technician could not determine the problem.which three tasks would be performed by the on site technician?(choose three)
  • Open the trouble ticket and enter customer information
  • REPLACE FAULTY CABLES OR CONECTIONS
  • Check to see if the ISP email server is working
  • CORRECT PC NETWORK SETTING AND RUN ANY NECESSARY UTILITIES
  • SWAP OUT SUSPECTED FAULTY HARDWARE WITH KNOWN GOOD HARDWARE
  • Check the statement account payment status
5.which two actions should be taken after a customer problem is resolved by the ISP help desk?(choose two)
  • Delete the trouble ticket from the database
  • DOCUMENT THE SOLUTION IN THE TROUBLE TICKET OR WORK ORDER
  • Escalate the trouble ticket to level 2 for future reference
  • File a work order for customer notification
  • COPY THE SOLUTION INTO A KNOWLEDGE BASE DOCUMENT FOR FUTURE REFERENCE
6.which two scenarios are common causes of physical network connectivity problems?(choose two)
  • Monitor unplugged
  • ETHERNETY CABLE PLUGGED INTO WRONG PORT
  • Incorrect default gateway
  • Unassigned IP address
  • FAULTY ETHERNET CABLE
7.click and drag the network component or function on the left to its associated layer on the right
Physical layer
repeater
Twisted fair cable
Data link layer
Switching
MAC address
Network layer
Routing
IP address
8.what two task should an on site technician perform before beginning any troubleshooting or repair at the customer site?(choose two)
  • REVIEW THE TROUBLE TICKET WITH THE CUSTOMER TO VERIVY INFORMATION IS CORRECT
  • Take damaged equipment to the ISP site for repair
  • Document the trouble shooting task performed and the solution
  • PROVIDE IDENTIFICATION,INCLUDING NAME AND PLACE OF EMPLOYMENT
  • Examine cabling to determine if it is faulty or connected into the wrong port
9.drag the technical skill on the left to the help desk activity on the right
Use analytical tools to provide a problem resolution
Speak in a calm,reassuring manner
Answer a call in friendly,professional manner
Make notes regarding the resolution of the helpdesk case
Get all relevant information from the customer
10.an ISP customer calls to report that the web server web-s1.cisco.com is not reachable through a web browser.the technician uses command line utilities to verivy problem and to begin the troubleshooting process.based on the result shown in the graphic,what two things can be determined about the problem?(choose two)
·         The web server at 192.168.0.10 is reachable from the source host
·         There is problem with the web server software on web –s1.cisco.com
·         A router is down between the source host and the server web-s1.cisco.com
·         DNS cannot resolve the IP address for the server web-s1.cisco.com
·         The default gateway between the source host and the server at 192.168.0.10 is down

ccna 2.1 quiz


1.Which is the function of the planning and provisioning team within the ISP organization?
·         Writing  service level agreements
·         Answering the help desk calls for the customer
·         Installing customer premises equipment
·         Managing the network operations center
·         IDENTIFYING WHETHER EXISTING NETWORK HARDWARE AND CIRCUITS ARE AVAILABLE
2.what are two characteristics of a scalable network?(choose two)
·         Easily overloaded with increased traffic
·         GROWS IN SIZE WITHOUT IMPACTING EXISTING USER
·         Is not as reliable as a small network
·         CONTAINS MODULAR DEVICES THAT ALLOW FOR EXPANSION
·         Offers limited number for applications
3.why do multiple ISPs connect to an IXP or a NAP?(choose two)
·         TO GAIN ACCESS TO EACH OTHER’S NETWORKS
·         To provide dial-up access for the customer
·         TO ACCESS THE INTERNET BACKBONE
·         To create large private network
·         To secure network transmission
4.why do small bussineses and individual choose DSL and cable connectivity instead of T3 conections?
·         DSL and cable connectivity offers higher speeds than T3 conection
·         T3 conection do not provide enough upload bandwidth to meet their needs
·         SERIAL T3 CONECTION ARE USUALLY MORE EXPENSIVE THAN DSL OR CABLE OPTION
·         T3 conection are less reliable than DSL and cable conections
5.a network administrator can successfully ping the server at www.cisco.com,but cannot ping the company web server located at an ISP in another city.which tools or command would help identify the specific router where the packet was lost or delayed?
·         Ipconfig
·         Netstat
·         telnet
·         TRACEROUTE
6.what make it possible for email to be sent and received on a wide variety devices,including cell phones,PDAs,laptops,and desktop computers?
·         All of devices run the same operating system software
·         There is a single provider of email server software
·         The device use the same email client software so they are compatible
·         EMAIL SOFTWARE IS WRITTEN USING STANDARD AND PROTOCOL THAT ENSURE COMPATIBILITY



7.click and drag the ISP service on the left to the description on the right

FTP hosting
Technical support
Equipment co-location
Application and media hosting

8.which connectivity options would be a good choice for a large university with three campus locations in the same major city?
·         Cable
·         DSL
·         T1
·         METRO ETHERNET

9.which statement describe a function by tier 3 internet service provider?
·         Peer with other similarly sized ISPs to from the global internet backbone
·         Own and operate undersea fiber runs  to provide internet connectivity across aceans
·         CONNECT INDIVIDUAL AND SMALL BUSSINESES TO THE INTERNET
·         Provide the link between tier 2 ISPs and the global internet backbone

Rabu, 10 November 2010

CCNA Discovery 2 Module 5 Exam Answers Version 4.0


CCNA Discovery 2 Module 5 Exam Answers Version 4.0
1. vIn what two ways does SDM differ from the IOS CLI? (Choose two.)
• SDM is used for in-band management only. The IOS CLI can be used for in-band and out-of-band management.
• SDM is accessed through a Telnet application. The IOS CLI is accessed through a web browser.
• SDM is available for all router platforms. The IOS CLI is available for a limited number of Cisco devices.
• SDM utilizes GUI buttons and text boxes. The IOS CLI requires the use of text-based commands.
• SDM is used for advanced configuration tasks. The IOS CLI is preferred for initial basic device configuration.

2. Which mode will a configured router display at login?
• global configuration mode
• setup mode
• ROM monitor mode
• user EXEC mode

3.
1
Refer to the exhibit. Which password or passwords will be encrypted as a result of the configuration that is shown?
• virtual terminal only
• enable mode only
• console and virtual terminal only
• enable mode and virtual terminal
• only the service password
• all configured passwords

4.
6
Refer to the exhibit. Which three sets of commands are required to enable administrators to connect to the Switch1 console over Telnet for configuration and management? (Choose three.)
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.64 255.255.255.192
• Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.2.66 255.255.255.192
• Switch1(config)# interface vlan 1
Switch1(config-if)# ip address 192.168.2.126 255.255.255.192
Switch1(config-if)# no shutdown
• Switch1(config)# line vty 0 4
Switch1(config-line)# enable password cisco
Switch1(config-line)# login
• Switch1(config)# line vty 0 15
Switch1(config-line)# password cisco
Switch1(config-line)# login
• Switch1(config)# ip default-gateway 192.168.2.65


5. How does the SYST LED on the catalyst 2960 switch indicate a POST failure?
• blinks rapidly amber
• blinks rapidly green
• steady amber
• steady green

6.
5
Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch X with a default gateway. Assuming that the switch IP address is 192.168.5.147/24, what command will the administrator use to assign a default gateway to the switch?
• X(config)# ip default-gateway 192.168.5.254
• X(config)# ip gateway 192.168.5.1
• X(config)# ip route 0.0.0.0 0.0.0.0 192.168.5.1
• X(config)# ip default-route 192.168.5.1
• X(config)# ip route 192.168.5.254 255.255.255.0 fastethernet 0/0

7. A technician has made changes to the configuration of a router. What command will allow the technician to view the current configuration before he saves the changes?
• router# show running-config
• router# show startup-config
• router# show flash
• router# show version

8. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
• VTY interface
• console interface

• Ethernet interface
• secret EXEC mode
• privileged EXEC mode
• router configuration mode

9. To save time, IOS commands may be partially entered and then completed by typing which key or key combination?
• Tab
• Ctrl-P
• Ctrl-N
• Up Arrow
• Right Arrow
• Down Arrow

10. What is the correct command sequence to configure a router host name to 'LAB_A'?
• Router> enable
Router# configure terminal
Router(config)# hostname LAB_A

• Router> enable
Router# hostname LAB_A
• Router> enable
Router# configure router
Router(config)# hostname LAB_A
• Router> enable
Router(config)# host name LAB_A

11.
3
Refer to the exhibit. From the router console, an administrator is unable to ping a Catalyst switch that is located in another building. What can the administrator do from her location to check the IP configuration of the attached switch?
• Open an SDM session with the switch from her desktop.
• Telnet to the switch from the router console.
• Use the show cdp neighbors detail command from the router console.
• The administrator must go to the switch location and make a console connection to check these settings.

12. Which two options must be selected in SDM Express to enable a router serial interface to obtain an IP address automatically? (Choose two.)
• Easy IP (IP negotiated)
• IP unnumbered
• No IP address
• HDLC encapsulation
• Frame Relay encapsulation
• PPP encapsulation

13. What three settings can be made in the SDM Express basic configuration screen? (Choose three.)
• host name
• DHCP options
• domain name
• interface IP addresses
• enable secret password
• DNS server IP addresses

14. Which tasks can be accomplished by using the command history feature? (Choose two.)
• View a list of commands entered in a previous session.
• Recall up to 15 command lines by default.
• Set the command history buffer size.
• Recall previously entered commands.
• Save command lines in a log file for future reference.

15. What option within Cisco SDM Express must be configured to allow hosts that receive IP address settings from the router to resolve names on the network or Internet?
• host name
• domain name
• DHCP address pool
• DNS server IP address

16. Which three encapsulation types can be set on a serial interface by an administrator who is using SDM Express? (Choose three.)
• ATM
• CHAP
• Frame Relay
• HDLC

• PAP
• PPP

17. Which command will display routing table information about all known networks and subnetworks?
• Router# show ip interfaces
• Router# show ip connections
• Router# show ip route
• Router# show ip networks

18. A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
• console
• AUX
• Telnet
• modem

19. Which three pieces of information about a neighbor device can be obtained by the show cdp neighbors command? (Choose three.)
• platform
• routing protocol
• connected interface of neighbor device
• device ID

• IP addresses of all interfaces
• enable mode password

20.
2
Which function is a unique responsibility of the DCE devices shown in the exhibit?
• transmission of data
• reception of data
• clocking for the synchronous link
• noise cancellation in transmitted data

21. Which of the following are functions of NVRAM? (Choose two.)
• stores the routing table
• retains contents when power is removed
• stores the startup configuration file

• contains the running configuration file
• stores the ARP table

22.
4
Refer to the exhibit. Which series of commands will enable users who are attached to Router1 to access the remote server?
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.125 255.255.255.252
Router1(config-if)# clock rate 64000
Router1(config-if)# no shutdown
• Router1(config)# interface S0/0/0
Router1(config-if)# ip address 64.100.0.129 255.255.255.252
Router1(config-if)# no shutdown


23. A network technician is attempting to add an older workstation to a Cisco switched LAN. The technician has manually configured the workstation to full-duplex mode in order to enhance the network performance of the workstation. However, when the device is attached to the network, performance degrades and excess collision are detected. What is the cause of this problem?
• The host is configured in a different subnet from the subnet of the switch.
• There is a duplex mismatch between the workstation and switch port.
• The switch port is running at a different speed from the speed of the workstation NIC.
• The host has been configured with a default gateway that is different from that of the switch.

24. Which of the following statements are true regarding the user EXEC mode? (Choose two.)
• All router commands are available.
• Global configuration mode can be accessed by entering the enable command.
• A password can be entered to allow access to other modes.
• Interfaces and routing protocols can be configured.
• Only some aspects of the router configuration can be viewed.

25. Which command turns on a router interface?
• Router(config-if)# enable
• Router(config-if)# no down
• Router(config-if)# s0 active
• Router(config-if)# interface up
• Router(config-if)# no shutdown

CCNA Discovery 2 Module 4 Exam Answers Version 4.0

CCNA Discovery 2 Module 4 Exam Answers Version 4.0
1. In an 8 bit binary number, what is the total number of combinations of the eight bits?
• 128
• 254
• 255
• 256
• 512
• 1024

2. Convert the decimal number 231 into its binary equivalent. Select the correct answer from the list below.
• 11110010
• 11011011
• 11110110
• 11100111
• 11100101
• 11101110

3. How many usable hosts are available given a Class C IP address with the default subnet mask?
• 254
• 255
• 256
• 510
• 511
• 512

4. Which statement describes NAT overload or PAT?
• Each internal address is dynamically translated to an individual external IP address.
• A single internal address is always translated to the same unique external IP address.
• Many internal addresses can be translated to a single IP address using different port assignments.
• Many internal addresses are statically assigned a single IP address and port to use for communications.

5. Which IPv4 class of addresses provides the most networks?
• Class A
• Class B
• Class C
• Class D
• Class E

6. Which statement accurately describes public IP addresses?
• Public addresses cannot be used within a private network.
• Public IP addresses must be unique across the entire Internet.
• Public addresses can be duplicated only within a local network.
• Public IP addresses are only required to be unique within the local network.
• Network administrators are free to select any public addresses to use for network devices that access the Internet.

7. Which two statements describe classful IP addresses? (Choose two.)
• It is possible to determine which class an address belongs to by reading the first bit.
• The number of bits used to identify the hosts is fixed by the class of the network.
• Only Class A addresses can be represented by high-order bits 100.
• Up to 24 bits can make up the host portion of a Class C address.
• Up to 24 bits can be used to identify unique networks.
• Three of the five classes of addresses are reserved for multicasts and experimental use.

8. Company XYZ uses a network address of 192.168.4.0. It uses the mask of 255.255.255.224 to create subnets. What is the maximum number of usable hosts in each subnet?
• 6
• 14
• 30
• 62

9. hat is the network broadcast address for a Class C address of 192.168.32.0 with the default subnet mask?
• 192.168.0.0
• 192.168.0.255
• 192.168.32.0
• 192.168.32.254
• 192.168.32.255

10.
1
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?
• The host subnet mask is incorrect.
• The default gateway is a network address.
• The default gateway is a broadcast address.
• The default gateway is on a different subnet from the host.

11. IPv6 increases the IP address size from 32 bits to how many bits?
• 64
• 96
• 128
• 192
• 256
• 512

12. What is the range of the first octet in a Class B address?
• 127 to 191
• 127 to 192
• 128 to 191
• 128 to 192

13. Which IPv4 class provides the highest number of host addresses per network?
• Class A
• Class B
• Class C
• Class D
• Class E

14.
2
refer to the exhibit. Which range of IP addresses would allow hosts that are connected to the Router1 Fa0/0 interface to access outside networks?
• 192.168.1.0 through 192.168.1.95
• 192.168.1.66 through 192.168.1.94
• 192.168.1.66 through 192.168.1.96
• 192.168.1.0 through 192.168.1.127
• 192.168.1.66 through 192.168.1.128

15. Which option shows the proper notation for an IPv6 address?
• 2001,0db8,3c55,0015,abcd,ff13
• 2001-0db8-3c55-0015-abcd-ff13
• 2001.0db8.3c55.0015.abcd.ff13
• 2001:0db8:3c55:0015::abcd:ff13

16. What are two reasons that NAT was developed? (Choose two.)
• to preserve registered public IP addresses
• to allow users on the public Internet to access local networks
• to provide a method for privately addressed LANs to participate in the Internet
• to make routing protocols operate more efficiently
• to allow private addresses to be routed on the public Internet
• to reduce overhead and CPU usage on gateway routers

17. What must happen for a privately addressed host on an inside local network to be able to communicate with an outside destination host on the Internet?
• The host IP address must be translated to an outside private address.
• The host IP address must be translated to an inside local address.
• The host IP address must be translated to an outside local address.
• The host IP address must be translated to an inside global address.

18. Which port numbers are used by PAT to create unique global addresses?
• 255 and below
• 1024 and below
• 1025 and above
• 64,000 and above

19. Static NAT works by mapping a specific inside local IP address to what other specific address type?
• inside global
• outside local
• outside global
• private IP address

20. What are three advantages of NAT implementations? (Choose three.)
• improved security
• improved router performance
• decreased processor load
• improved scalability
• universal application compatibility
• sharing few public IP addresses with many hosts

lab activity 3.2.4.2


Tujuan• Memeriksa denah ada pelanggan.• Mengusulkan rencana kabel upgrade untuk mengakomodasi ruang lantai tambahan.Latar Belakang / PersiapanSebuah perusahaan menengah memiliki ruang yang ada di lantai dua sebuah menara kantor dan baru saja memperoleh sisa lantai dua. Mereka menanyakan anda untuk memeriksa rencana denah yang ada mereka dan membantu mereka dalam penempatan penempatan baru IDF, kabel untuk mendukung semua ruang kantor baru, dan untuk membantu menentukan apakah semua perangkat yang baru diperlukan.Laboratorium ini dapat dilakukan secara individu maupun kelompok.Sumber berikut diperlukan:• Rencana Lantai ada (disediakan)Langkah 1: Memeriksa rencana lantai yang ada.a. Dari informasi yang diberikan mengenai rencana lantai yang ada, label item berikut:1) POP - Point of Presence2) MDF - Fasilitas Distribusi Utama3) IDF - Fasilitas Distribusi Intermediate4) Vertikal / Backbone pengkabelan5) Kabel horisontal
b. Apa jenis pemasangan kabel dapat digunakan untuk pemasangan kabel / tulang punggung vertikal? Jelaskan jawaban Anda.
(fiber Optic)Langkah 2: Rencana Evaluasi untuk ruang lantai baru.AnyCompany baru saja bergabung dengan sebuah kelompok desain web kecil dan telah mendapatkan ruang yang tersisa di lantai dua untuk mengakomodasi tim desain web. Ruang baru ini diwakili pada diagram sebagai ruang lantai disorot pada sisi kanan floorplan tersebut. Telah diputuskan untuk menambahkan IDF kedua untuk mendukung workstation di daerah baru.a. Sarankan lokasi yang mungkin untuk IDF baru. Apa ruangan / lokasi yang Anda pilih dan menjelaskan mengapa Anda pikir itu cocok?
b. Apa jenis kabel yang akan Anda sarankan untuk pemasangan kabel vertikal yang diperlukan untuk menghubungkan IDF baru ke MDF ada? Jelaskan alasan Anda.
c. Ruang yang baru berisi kebanyakan kantor. Asumsikan bahwa kantor masing-masing akan ditetapkan dengan 2 tetes data. Juga rencana untuk 2 tetes di auditorium untuk mendukung akses Internet untuk presentasi dan sesi pelatihan. Berapa banyak tetes data tambahan perlu dipesan?
d. Anda telah diminta untuk menentukan jumlah baru 24 port switch yang diperlukan untuk IDF baru. Jangan lupa untuk merencanakan pertumbuhan sekitar 25%. Berapa banyak switch baru AnyCompany perlu membeli?
e. Berapa banyak kabel horizontal akan berakhir pada panel patch di IDF yang baru? €Langkah 3: Periksa ruang lantai dan rencana kabel. a. Apa tetap selain switch yang Anda harapkan untuk temukan di IDF yang baru? b. Apa tetap selain switch yang Anda harapkan untuk temukan di MDF?
c. Menggunakan kabel yang ada berjalan, bisa Anda gunakan UTP untuk menghubungkan perangkat di kamar 2,20 atau 2,30 langsung ke switch di MDF?

Langkah 4. Refleksi
 Dengan satu atau dua teman sekelas, diskusikan hal berikut: a. Apakah lebih baik memiliki IDF dalam ruang lantai atau harus perusahaan menjalankan kabel horizontal untuk setiap perangkat langsung kembali ke MDF ada?
b. Berapa banyak akan diperlukan kabel dari MDF ke IDF untuk mendukung switch? Jelaskan jawaban Anda.


GAMBAR PENDUKUNG:
https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEiEXll7zcnsQiv_VM1UXvLMqwdVTUB3O-Mt0Lkcfe-TeIVS3tn6IlcPv64yV3jOsz8aKYcMmiVurcZqQ2Qf0w30-RGTLzsEKwzOS4Y7i3Qqgv5Ydg1SkUkwzMQRy4MvVBAPkkab4U7wonk/s320/6.bmp


kesimpulan dari pertanyaan:
atau lab actifity diatas:
* MDF (Main Distribution Frame) : adalah sebuah tempat terminasi kabel yang menghubungkan kabel saluran pelanggan dari sentral telepon dan jaringan kable yang menuju ke terminal pelanggan. Bila sebuah sentral telepon memiliki 1000 pelanggan, maka pada MDF-nya akan terdapat 1000 pasang kabel tembaga yang terpasang pada slot MDF-nya, dimana setiap pasang kabel tembaga ini akan mewakili satu nomor pelanggan. Dan 1000 pasang kabel yeng terpasang di slot MDF ini akan di-cross coneect dengan 1000 pasang kable lain yang berasal dari saluran pelanggan yang menuju ke pesawat terminal pelanggan. Jadi bila seorang pelanggan ingin agar nomor teleponnya diganti dengan nomor lain, maka proses perubahan nomor ini dapat dengan mudah dilakukan dengan merubah koneksi saluran pelanggan di MDF-nya. MDF bisanya diletakan pada satu gedung yang sama dengan sentral teleponnya (berdekatand engansentral telepon).
Jaringan dibagi

Berhasil umum jaringan data center dapat dibagi menjadi sebagai berikut:

1, pusat data manajemen perusahaan jaringan kantor

Jaringan untuk pengelolaan hari ke kantor perusahaan hari dan digunakan untuk menyediakan platform internet akses jaringan, melalui jaringan virtual untuk mencapai pembagian pembatasan koneksi internet.

2, perusahaan manajemen jaringan demonstrasi uji

Manajemen jaringan perusahaan untuk menampilkan web hosting layanan demo platform, perusahaan manajemen jaringan jaringan kantor setiap hari dengan setiap isolasi fisik lainnya, sementara beberapa bidang manajemen bisnis jaringan sebagai kawasan pengembangan uji.

3, host jaringan pelanggan kantor

Jaringan dikelola Layanan ini menyediakan pelanggan dengan kantor leasing dan akses Internet untuk penggunaan sehari-hari untuk menyediakan platform jaringan, dibagi dengan jaringan virtual untuk mencapai isolasi pengguna perusahaan yang berbeda.

Sementara beberapa memiliki persyaratan khusus Hu Ke, independen dari antarmuka outreach.

4, host jaringan pelanggan produksi

Proyek berbasis web, jaringan yang paling penting, dapat dibagi menjadi dua kasus untuk dipertimbangkan:

1) Pengelolaan pelanggan outreach dipinjam garis dan garis kabel internal.

Pengkabelan menggunakan MDA --- --- EDA HDA kabel data center, sesuai dengan tata letak rak kamar mesin menyiapkan jaringan kabinet pertama, diletakkan oleh jaringan serat multimode kamar mesin dan jaringan Gigabit tembaga untuk melawan yang pertama, dan kemudian diletakkan di bawah kebutuhan spesifiktembaga dan kabel serat optik untuk kabinet EDA.

2) Pelanggan outreach garis bangunan independen, untuk meminjam garis kabel internal.

Beberapa pelanggan mungkin meminta Unicom eksternal yang independen, dan dapat mempertimbangkan setiap kamar sejumlah serat single-mode instalasi kabel optik dan kabel koaksial.

Ke dalam setiap kamar jembatan adalah menyisihkan marjin tertentu, untuk memenuhi kebutuhan pelanggan yang berbeda, dan jembatan daerah seharusnya mampu mempertahankan posisi.

5, pengembangan dan pengujian web hosting pelanggan

Jaringan terutama menyediakan jaringan dan sistem dikelola lokasi pengujian host, jaringan yang terkait dengan jaringan lain pada prinsipnya, dan sebuah bangunan terpisah untuk setiap nasabah.

Pemasangan kabel antara perangkat dan lemah set

Set kabel terintegrasi antara ruang peralatan dan yang lemah, termasuk:

Penggunaan Kamar

Telekomunikasi operator ke ruang akses kawat kabel; (untuk kedua arah dari saluran akses)

Lemah antar-lantai MDF IDF

Komunikasi operator ruang akses / DC peralatan jaringan akses ruang komunikasi operator jaringan pusat komputer dan ruang (MDF)

lantai kantor Dikelola pengguna mempertimbangkan dikelola klien jaringan kantor IDF IDF

Pemasangan kabel perencanaan awal

Pusat data total empat unit jaringan komunikasi akses, akses ke sumber daya dari semua akses ruang komunikasi operator ke ruang tandem jaringan (jaringan ruang mesin) manajemen terpadu dan distribusi.

Untuk pengguna biasa dikelola sesuai dengan luas lantai ruangan perencanaan routing daerah, setiap konfigurasi jaringan meja pertama.

Untuk pengguna hosting Kamar VIP lantai kamar, masing-masing kolom rak konfigurasi jaringan meja pertama.

Jaringan tandem kamar ke kamar lantai bagasi kabel meletakkan di antara lemah dan tembaga, dan kemudian melompat dari antar lemah-terhubung ke semua pelanggan dikelola jaringan counter ruang pertama, konfigurasi spesifik jumlah cahaya tembaga luas lantai bawah dan daerah untuk menentukan.

Manajemen kantor staf dan pelanggan dapat berbagi set OA dikelola jaringan kantor, jaringan dapat terhubung dengan Internet.

Pelanggan kantor setiap stasiun kantor informasi umum dapat dikonfigurasi empat poin (tiga data, satu suara), salah satu data titik sebagai jaringan informasi OA poin kantor, sebuah titik data sebagai titik pelanggan informasi manajemen perangkat daerah ruangan, Anda dapatmenerima serangkaian ruang tari sederhana, satu titik data sebagai cadangan.